Chishui Guangxi Charging Pile Project
3. Power requirements: ① Input voltage: single-phase 220V; ② Output power: single-phase 220V/5KW; ③ Frequency: 50Hz ± 2Hz; ④ Allowable voltage fluctuation range: single-phase 220V ± 15%; 4. Electrical requirements: ① After the correct connection of plug and socket is confirmed to be successful, the circuit that can be opened and closed with load can be closed to supply power to the socket; ② The leakage protection device shall be installed on the incoming side of the power supply cable; ③ The protection of low-voltage distribution equipment and lines shall meet the relevant provisions in the Code for Design of Low Voltage Power Distribution (GB/50053); ④ For the distribution line of IT system, in case of ground fault, the insulation monitoring device shall send out audio or light signals. In case of the second phase to phase ground fault, the fault circuit shall be cut off by the over-current protection appliance or leakage current action protector; ⑤ In the lighting distribution system, the lighting and socket circuits should not be powered by the same circuit.
Chishui Guangxi Charging Pile Project
In addition, according to the different ways of energy conversion when charging the electric vehicle battery, charging devices can be divided into contact type and induction type. With the rapid development of power electronics technology and converter control technology, the maturity and popularization of high-precision controllable converter technology, the phased constant current charging mode has been basically replaced by the constant voltage current limiting charging mode with continuous changes in charging current and charging voltage. The constant voltage current limiting charging mode dominates the charging process. The big problem of contact charging is its safety and versatility. In order to make it meet the strict safety charging standard, many measures must be taken in the circuit to enable the charging equipment to charge safely in various environments. Constant voltage current limiting charging and phased constant current charging are both contact charging technologies. New induction charging technology for electric vehicles has developed rapidly.
Chishui Guangxi Charging Pile Project
On board charging device refers to the device installed on the electric vehicle that uses the ground AC power grid and the on-board power supply to charge the battery pack, including the on-board charger (Figure 1-13), the on-board charging generator set and the operating energy recovery charging device. A AC power cable with a plug is directly inserted into the charging socket of the electric vehicle to charge the battery. On board charging devices usually use contact chargers with simple structure and convenient control, or inductive chargers. It is designed completely according to the type of on-board battery, with strong pertinence. Off board charging device, i.e. ground charging device, mainly includes special charger, special charging station, general charger, charging station for public places (Figure 1-14), etc. It can meet various charging modes of various batteries. Generally, the off board charger has large power, volume and weight to adapt to various charging modes.
Chishui Guangxi Charging Pile Project
In this environment, major automobile manufacturers in the automobile industry are also constantly shifting their focus to the research and development of new energy vehicle technology, and have also launched many new energy vehicles to replace oil with electricity and reduce emissions. This also represents the new direction of future automobile development. In China, friends who pay more attention to cars can see that more and more new energy vehicles are running on the road. More people are also aware of the benefits that new energy vehicles bring to the earth. The country is also introducing various preferential policies to vigorously promote the development of new energy vehicles. However, the main reason why some people are unwilling to buy new energy vehicles is the lack of endurance and inconvenient charging. However, with the continuous popularity of electric vehicles, these problems will certainly be solved in the future. Previously, the country also made a series of decisions in order to facilitate the charging of cars in the future.
Chishui Guangxi Charging Pile Project
How to properly charge in the hot link when using the charging pile of new energy vehicles? 1. Take care of your electric donkey and don't let it get sunburnt: in hot summer, you often sweat, and the rechargeable battery often "gets high fever". Here, it is recommended that the owner choose a place with a parking shed or a barrier to cover the electric vehicle as far as possible, and don't let the electric vehicle be exposed to the sun immediately, which will endanger the service life of the vehicle. In addition, fire accidents are very likely to occur under high temperatures. 2. Do not "steam up and cook down": the temperature is already hot. If the electric car is exposed to the sun at the moment, but you are charging the car, the rechargeable battery will generate heat in the whole process of charging. At this time, all cars are in the "steam up and cook down" mode, and you will "deploy" carelessly. 3. The electric vehicle must also take a proper "rest". 4. The charging time must be well controlled.
